Eaton 5SC1000 vs CyberPower CP1000PFCLCD: 700W or 600W?
Quick answer: Eaton 5SC1000 and CyberPower CP1000PFCLCD are both 1000VA line-interactive sine-wave UPS towers, but Eaton is rated for 700W and supplies eight battery-backed AC outlets. CyberPower is rated for 600W and provides five battery-backed outlets plus five surge-only outlets. Eaton’s communications and all-backed-up socket layout may suit a small server stack; CyberPower is a compact PFC Sinewave option for a desktop or NAS setup where five backed-up sockets suffice.
Read the exact Eaton 5SC1000 model record and CyberPower CP1000PFCLCD model record. Check purchase options for 5SC1000 or CP1000PFCLCD; compare current seller, model revision and battery cost before ordering.
Affiliate disclosure: This page may earn a commission from qualifying purchases through retailer links.
Eaton 5SC1000 vs CP1000PFCLCD: model-specific differences
| Specification | Eaton 5SC1000 | CyberPower CP1000PFCLCD |
|---|---|---|
| VA / watt rating | 1000VA / 700W | 1000VA / 600W |
| Topology | Line interactive with AVR | Line interactive with AVR |
| Battery waveform | Sine wave | Sine wave |
| AC outlets | 8 total | 10 total |
| Battery-backed outlets | 8 | 5 |
| Surge-only outlets | 0 | 5 |
| Communication | USB HID and RS-232 | USB and relay |
| Software ecosystem | Eaton Intelligent Power Manager | PowerPanel Personal |
| Listed dimensions (H × W × D) | 8.2 × 5.9 × 13.4 in | 9.7 × 3.94 × 10.24 in |
| User-replaceable battery | Yes | Yes |
Seven hundred watts versus six hundred: decide from measured load
Both carry a 1000VA label, but Eaton’s watt limit is 100W higher. For a 400W measured load, the 5SC1000 has 300W of rated headroom and the CyberPower has 200W. Neither calculation establishes backup minutes, and both should be checked against a runtime chart for the actual connected equipment.
A small NAS, router and switch may draw far less than 400W; in that case the extra 100W ceiling may not affect the purchase. A compact server and PoE switch may create higher peaks, making the Eaton’s larger limit more useful. Avoid sizing from a PC power-supply nameplate or from VA alone.
Eight battery-backed sockets versus five
Eaton’s eight NEMA 5-15R outlets are battery-backed. CyberPower has ten AC outlets, but only five provide battery backup; the other five are surge-only. This distinction is especially important in a network closet where a firewall, router, switch, NAS and host all need to remain online long enough to shut down safely.
More backed-up sockets do not mean more usable wattage or longer battery life. Put only the devices needed for an orderly shutdown on battery. If your setup includes several AC adapters, check plug spacing and whether a suitable power-distribution arrangement is supported.
Shutdown software is a purchase requirement, not an afterthought
Eaton documents standard USB HID and RS-232 connections for the 5SC1000. CyberPower documents USB and relay communication plus PowerPanel Personal for CP1000PFCLCD. The interfaces and management software are different, so check the operating system, NAS firmware and shutdown method that will actually be used.
For one NAS, confirm that its UPS support list or software recognizes the exact unit. For several hosts, decide which device monitors the UPS and how other systems receive the low-battery event. If the switch carries the shutdown messages, it must remain powered until those messages are delivered. The UPS data-connection guide explains why a charging socket is not a monitoring interface.
The NAS storage plan can change the electrical load
Adding drives or upgrading to a larger NAS can change the protected load and the number of devices connected. DiskBarn’s RAID and NAS capacity calculator helps plan drive count and usable storage; it does not estimate electrical draw. After deciding on storage hardware, measure or estimate the actual watts separately before choosing a UPS.
Battery replacement, runtime and physical fit
Both are lead-acid systems with user-replaceable batteries. Eaton highlights its ABM battery-management system, while CyberPower offers its PFC Sinewave features and a relatively narrow mini-tower footprint. Verify replacement cartridge identity, the unit’s clearance and the cost of service over the intended ownership period.
Eaton’s published warranty information includes conditions tied to registration and different coverage descriptions; check the terms for the exact seller and region. CyberPower lists a three-year warranty for CP1000PFCLCD. Neither warranty statement substitutes for checking the current retailer return policy or availability.
Buying decision
- Choose Eaton 5SC1000 if the measured load benefits from a 700W limit, you need more than five backed-up AC outlets, or its USB-HID/serial integration fits the intended server environment.
- Choose CyberPower CP1000PFCLCD if a 600W ceiling is adequate, five backed-up outlets cover the critical equipment and its PowerPanel/USB integration matches the host.
- Do not choose by VA alone. Confirm manufacturer runtime at your actual load, replacement-battery cost and compatibility. Compare the two models and review the UPS sizing guide if the load is uncertain.
Questions buyers ask
Does the Eaton run longer because it has 700W?
Not necessarily. A 700W rating is a higher output limit, not proof of more battery runtime at the same load.
Are all ten CyberPower outlets battery-backed?
No. Five provide battery backup and five provide surge protection only. Eaton lists eight battery-backed outlets.
Will either automatically shut down every NAS?
No universal guarantee. Verify the exact NAS and UPS communication compatibility and test a controlled shutdown.
Primary manufacturer sources
Model specifications: Eaton 5SC1000 product information and CyberPower CP1000PFCLCD product information. Reviewed October 22, 2026. Confirm retail availability and warranty details before purchase.
